-
1 изоляция жилы
- Leiterisolierung, f
- Isolierhülle, f
изоляция жилы
изоляция наложенная на токопроводящую жилу или экран по жиле
[IEV number 461-02-02]EN
conductor insulation
insulation applied on a conductor or a conductor screen
[IEV number 461-02-02]FR
enveloppe isolante
isolation appliquée sur une âme ou sur un écran sur âme
[IEV number 461-02-02]Тематики
- кабели, провода...
EN
DE
- Isolierhülle, f
- Leiterisolierung, f
FR
Русско-немецкий словарь нормативно-технической терминологии > изоляция жилы
-
2 длительный допустимый ток
- Strombelastbarkeit, f
- Dauerstrombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-немецкий словарь нормативно-технической терминологии > длительный допустимый ток
-
3 изолированный провод
- Ader, f
изолированный провод
—
[Я.Н.Лугинский, М.С.Фези-Жилинская, Ю.С.Кабиров. Англо-русский словарь по электротехнике и электроэнергетике, Москва, 1999 г.]EN
core insulated conductor
assembly comprising a conductor and its own insulation (and screens, if any)
[IEC 61892-4, ed. 1.0 (2007-06)]
core-insulated conductor (North America)
assembly comprising a conductor and its own insulation (and screens, if any)
NOTE In North American usage, the core of a cable has been defined as the assembly of components of a cable lying under a common covering such as the sheath (jacket).
[IEC 60092-350, ed. 3.0 (2008-02)]FR
conducteur (isolé)
ensemble comprenant l'âme, son enveloppe isolante et ses écrans éventuels
Note – En Amérique du Nord le terme “core of a cable” a été défini comme l'ensemble des constituants d'un câble disposés sous un revêtement commun, tel que la gaine. L'utilisation de ce terme est déconseillée dans ce sens.
[ IEV ref 461-04-04]Рис. Schneider Electric
Параллельные тексты EN-RU
An insulated conductor is made up of a conductor core and its
insulating envelope.
[Schneider Electric]Изолированный провод состоит из токопроводящей жилы и изоляции провода.
[Перевод Интент]Тематики
- кабели, провода...
EN
- core insulated conductor
- core-insulated conductor
- covered conductor
- covered wire
- insulated conductor
DE
- Ader, f
FR
Русско-немецкий словарь нормативно-технической терминологии > изолированный провод
-
4 замыкание на землю
замыкание на землю
Случайный электрический контакт между токоведущими частями, находящимися под напряжением, и землей.
[ПУЭ]
замыкание на землю
Замыкание, обусловленное соединением с землей.
[ ГОСТ 26522-85]
замыкание на землю
Состояние, характеризующееся возникновением случайной проводящей цепи между проводником, находящимся под напряжением, и землей.
Примечание - Проводящая цепь может проходить через поврежденную изоляцию, строительные конструкции (колонны, леса, краны, лестницы) или растения (деревья, кусты) и может иметь значительное полное сопротивление.
[ ГОСТ Р МЭК 60050-195-2005]EN
earth fault
occurrence of an accidental conductive path between a live conductor and the Earth
NOTE – The conductive path can pass through a faulty insulation, through structures (e.g. poles, scaffoldings, cranes, ladders), or through vegetation (e.g. trees, bushes) and can have a significant impedance.
[IEV number 195-04-14]FR
défaut à la terre
occurrence d’un chemin conducteur accidentel entre un conducteur sous tension et la Terre
NOTE – Le chemin conducteur peut passer par une isolation défectueuse, par des structures (par exemple supports de ligne, échafaudages, grues, échelles), ou encore par la végétation (par exemple arbres, buissons) et peut présenter une impédance non négligeable.
[IEV number 195-04-14]Параллельные тексты EN-RU
The earth fault, caused by an insulation loss between a live conductor and an exposed conductive part, represents a plant engineering problem which may cause damage to the electrical installations and above all may jeopardize people; as a matter of fact, people could get in touch with an exposed-conductive-part not normally live but which, due to the fault, might have a dangerous potential to ground.
[ABB]Замыкание на землю, вызванное повреждением изоляции между токоведущим проводником и открытой проводящей частью, представляют определенную проблему при эксплуатации электроустановок, поскольку такая неисправность может привести к выходу электрооборудования из строя и, кроме того, подвергает людей опасности поражения электрическим током. Это объясняется тем, что становится возможным прикосновение к открытой проводящей части, которая в нормальных условиях не находится под напряжением, но из-за повреждения изоляции может приобрести опасный потенциал относительно земли.
[Перевод Интент]Тематики
EN
- earth
- earth connection
- earth fault
- ground
- ground connection
- ground fault (US)
- ground short circuit
- grounding connection
- line-to-ground fault
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > замыкание на землю
-
5 неподготовленный проводник
неподготовленный проводник
Проводник отрезанный и с удаленной изоляцией для вставки в вывод.
Примечание. К неподготовленным относятся проводники, форма которых изменена для вставки в вывод или жилы которых скручены для упрочнения конца
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
проводник, не подготовленный к присоединению
-
[IEV number 442-01-26]EN
unprepared conductor
conductor which has been cut and the insulation of which has been removed for insertion into a terminal
NOTE - A conductor, the shape of which is arranged for introduction into a terminal or the strands of which are twisted to consolidate the end is considered to be an unprepared conductor.
[IEC 61095, ed. 2.0 (2009-02)]
[IEV number 442-01-26]FR
conducteur non préparé
conducteur qui a été coupé et dont l'isolation a été retirée en vue de son insertion dans une borne
NOTE - Un conducteur dont la forme est arrangée pour qu'il soit dans une borne ou dont les torons sont torsadés pour en consolider l'extrémité est considéré comme un conducteur non préparé
[IEC 61095, ed. 2.0 (2009-02)]
[IEV number 442-01-26]Проводник с удаленной изоляцией и с уплотненным концом многопроволочной жилы
Проводник с частично снятой (прорезанной) изоляцией
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > неподготовленный проводник
-
6 контактное соединение с прокалыванием изоляции
- Schneidklemmverbindung, f
- Durchdringverbindung, f
контактное соединение с прокалыванием изоляции
-EN
insulation piercing connection (of electronic equipment)
solderless connection made by metallic protruding elements which pierce the insulation and are intended to provide contact with the conductor by deforming or penetrating it
[IEV number 581-23-34]FR
connexion à percement d’isolant (dans l’équipement électronique)
connexion sans soudure obtenue au moyen d'éléments perforants métalliques, qui percent l'isolant et établissent le contact par déformation ou pénétration du conducteur
[IEV number 581-23-34][http://www.energosever.ru/armatura_sip-simel.html]
Контактные пластины прокалывают изоляцию и обеспечивают надежный контакт с жилой
[В. Ф. Лярский, О. Б. Мурадян. Электрические соединители. Справочник. Радио и связь, 1988]Присоединение кабеля к контактам способом прокалывания изоляции
Тематики
EN
DE
- Durchdringverbindung, f
- Schneidklemmverbindung, f
FR
- connexion à percement d’isolant
Русско-немецкий словарь нормативно-технической терминологии > контактное соединение с прокалыванием изоляции
-
7 изолированная жила (термин употребляется в Северной Америке)
- Ader, f
изолированная жила (термин употребляется в Северной Америке)
совокупность элементов, состоящая из жилы, ее изоляции (и экранов, если они есть)
Примечание. В Северной Америке термин «core of a cable» определяется как совокупность компонентов кабеля, расположенных под общим защитным покровом, таким как оболочка. Такое применение этого термина не допустимо
[IEV number 461-04-04]EN
core
insulated conductor
assembly comprising a conductor with its own insulation (and screens if any)
NOTE – In North American usage, the core of a cable has been defined as the assembly of components of a cable lying under a common covering such as the sheath. Such usage is deprecated.
[IEV number 461-04-04]FR
conducteur (isolé)
ensemble comprenant l'âme, son enveloppe isolante et ses écrans éventuels
NOTE – En Amérique du Nord le terme “core of a cable” a été défini comme l'ensemble des constituants d'un câble disposés sous un revêtement commun, tel que la gaine. L'utilisation de ce terme est déconseillée dans ce sens.
[IEV number 461-04-04]Тематики
- кабели, провода...
EN
DE
- Ader, f
FR
Русско-немецкий словарь нормативно-технической терминологии > изолированная жила (термин употребляется в Северной Америке)
-
8 ток защитного проводника
- Schutzleiterstrom, m
ток защитного проводника
Электрический ток, возникающий в защитном проводнике, такой как, например, ток утечки, или электрический ток, возникающий в результате повреждения изоляции
[ ГОСТ Р МЭК 60050-826-2009]
ток защитного проводника
Ток, проходящий через защитный проводник.
Примечание - Этот ток может повлиять на работу устройств защиты от остаточного тока, присоединенных к той же цепи.
[ ГОСТ Р МЭК 60598-1-2011]EN
protective conductor current
electric current appearing in a protective conductor, such as leakage current or electric current resulting from an insulation fault
[IEV number 826-11-21]FR
courant dans le conducteur de protection, m
courant électrique apparaissant dans un conducteur de protection, tel que courant de fuite ou courant électrique du à un défaut d’isolation
[IEV number 826-11-21]Тематики
EN
DE
- Schutzleiterstrom, m
FR
- courant dans le conducteur de protection, m
Русско-немецкий словарь нормативно-технической терминологии > ток защитного проводника
-
9 разделитель
- Trennschicht (eines Kabels), f
разделитель
Тонкий слой, выполняющий роль барьера, предупреждающего взаимное вредное воздействие различных компонентов кабеля друг на друга таких, как токопроводящая жила и изоляция или изоляция и оболочка.
[IEV number 461-05-01]EN
separator
thin layer used as a barrier to prevent mutually detrimental effects between different components of a cable, such as between the conductor and insulation or between insulation and sheath
[IEV number 461-05-01]FR
séparateur
couche mince utilisée comme barrière pour éviter les interactions nocives entre deux constituants d'un câble, par exemple entre âme et enveloppe isolante ou entre enveloppe et gaine
[IEV number 461-05-01]Тематики
- кабели, провода...
EN
DE
- Trennschicht (eines Kabels), f
FR
Русско-немецкий словарь нормативно-технической терминологии > разделитель
-
10 модифицированная накрутка
- modifizierte Wickelverbindung, f
модифицированная накрутка
Накрутка, выполняемая таким образом, что с несколькими виками оголенного провода накручиваются 2-3 витка изолированного провода. Такая накрутка более устойчива к воздействию вибрации.
[В. Ф. Лярский, О. Б. Мурадян. Электрические соединители. Справочник. Радио и связь, 1988]EN
modified wrapped connection
wrapped connection achieved by wrapping an insulated solid conductor around a wrap post in such a way that the insulation of the conductor covers the outer sides of wrap at at least three corners of the wrap post
[IEV number 581-23-36]FR
connexion enroulée renforcée
connexion enroulée obtenue par enroulement d'un conducteur isolé massif autour d'une borne pour connexion enroulée de manière à ce que l'isolant du fil soit en contact avec au moins trois arêtes de la borne pour connexion enroulée
[IEV number 581-23-36]
а) обычная накрутка; б) - модифицированная накрутка
[В. Ф. Лярский, О. Б. Мурадян. Электрические соединители. Справочник. Радио и связь, 1988]Тематики
EN
DE
- modifizierte Wickelverbindung, f
FR
Смотри также
Русско-немецкий словарь нормативно-технической терминологии > модифицированная накрутка
11 обычная накрутка
- konventionelle Wickelverbindung, f
обычная накрутка
Накрутка, выполняемая только витками оголенного провода без накручивания витков изолированного провода.
[Интент]EN
conventional wrapped connection
wrapped connection achieved by wrapping an insulated solid conductor around a wrap post in such a way that the insulation of the conductor does not cover the wrap post anywhere
[IEV number 581-23-37]FR
connexion enroulée simple
connexion enroulée obtenue par enroulement d'un conducteur isolé massif autour d'une borne pour connexion enroulée de manière à ce que l'isolant du fil ne soit nulle part en contact avec la borne pour connexion enroulée
[IEV number 581-23-37]
а) обычная накрутка; б) - модифицированная накрутка
[В. Ф. Лярский, О. Б. Мурадян. Электрические соединители. Справочник. Радио и связь, 1988]Тематики
EN
DE
- konventionelle Wickelverbindung, f
FR
Смотри также
Русско-немецкий словарь нормативно-технической терминологии > обычная накрутка
12 разъемный трансформатор тока
разъемный трансформатор тока
Трансформатор тока без первичной обмотки, магнитная цепь которого может размыкаться и затем замыкаться вокруг проводника с измеряемым током.
[ ГОСТ 18685-73]EN
split core type current transformer
a current transformer without primary conductor, and primary insulation of its own, the magnetic circuit of which can be hinged open (or otherwise separated into two parts) and then closed around the insulated conductor carrying the current to be measured
[IEV number 321-02-05]FR
transformateur de courant à circuit magnétique ouvrant
transformateur de courant sans enroulement primaire et sans isolation propre dont le circuit magnétique peut être ouvert puis refermé autour d'un conducteur isolé parcouru par le courant à mesurer
[IEV number 321-02-05]
[http://www.rusotools.ru/offers/8774/разъемный-трансформатор-тока-тзрл-125-у3.html]
Трансформатор выполнен в виде опорной разъемной конструкции. Роль первичной обмотки выполняет трехфазный кабель на напряжение до 10 кВ, пропущенный в окно трансформатора. Вторичная обмотка намотана на тороидальный магнитопровод, разрезанный пополам. Обе части, залитые изоляционным компаундом на основе эпоксидной смолы, соединяются болтами. Опорой трансформатора служит основание изоляционного корпуса со специальными втулками для крепления[http://www.laborant.ru/eltech/02/4/1/27-99.htm]
Недопустимые, нерекомендуемые
- разборный трансформатор
- расчленяемый трансформатор тока
- трансформатор тока с раздельным сердечником
- трансформатор тока с расчленяемым сердечником
Тематики
Классификация
>>>Синонимы
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > разъемный трансформатор тока
13 ввод (проходной изолятор)
- Durchführung, f
ввод
Проходной изолятор, имеющий внутреннюю изоляцию из жидкого, твердого, газообразного диэлектрического материала или их комбинации.
[ ГОСТ 27744-88 ]EN
bushing
device that enables one or several conductors to pass through a partition such as a wall or a tank, and insulate the conductors from it.
NOTE 1 – The means of attachment (flange or fixing device) to the partition forms part of the bushing. The conductor may form an integral part of the bushing or be drawn into the central tube of the bushing.
NOTE 2 – The bushings may be of the following types:
- liquid-filled bushing;
- liquid-insulated bushing;
- gas-filled bushing;
- gas-insulated bushing;
- oil-impregnated paper bushing;
- resin-bonded paper bushing;
- resin-impregnated paper bushing;
- ceramic, glass or analogous inorganic material bushing;
- cast or moulded resin-insulated bushing;
- combined insulation bushing;
- compound-filled bushing;
- gas-impregnated bushing.
[IEV number 471-02-01]FR
traversée
dispositif servant à faire passer un ou plusieurs conducteurs à travers une paroi, telle qu’un mur ou une cuve, en isolant le(s) conducteur(s) de cette paroi.
NOTE 1 – Les moyens de fixation (bride ou autre dispositif) sur la paroi font partie de la traversée. Le conducteur peut être solidaire de la traversée ou démontable.
NOTE 2 – Les différentes traversées peuvent être les suivantes:
- traversée à remplissage d’un liquide;
- traversée à isolation liquide;
- traversée à remplissage de gaz;
- traversée à isolation gazeuse;
- traversée en papier imprégné d’huile;
- traversée en papier enduit de résine;
- traversée en papier imprégné de résine;
- traversée en matière céramique, en verre ou en matière inorganique analogue;
- traversée à isolation en résine coulée ou moulée;
- traversée à isolation combinée;
- traversée à remplissage de mélange;
- traversée imprégnée de gaz.
[IEV number 471-02-01]Тематики
EN
DE
- Durchführung, f
FR
Русско-немецкий словарь нормативно-технической терминологии > ввод (проходной изолятор)
14 защита от замыкания на землю
- Erdkurzschlussschutz, m
защита от замыканий на землю
Защита, предназначенная срабатывать при замыканиях на землю в энергосистеме.
[Разработка типовых структурных схем микропроцессорных устройств РЗА на объектах ОАО "ФКС ЕЭС". Пояснительная записка. Новосибирск 2006 г.]EN
earth-fault protection
ground-fault protection (US)
protection intended to operate for power system earth faults
[IEV ref 448-14-28]FR
protection de défaut à la terre
protection destinée à fonctionner en cas de défaut à la terre dans le réseau d'énergie
[IEV ref 448-14-28]Параллельные тексты EN-RU
The earth fault, caused by an insulation loss between a live conductor and an exposed conductive part, represents a plant engineering problem which may cause damage to the electrical installations and above all may jeopardize people; as a matter of fact, people could get in touch with an exposed-conductive-part not normally live but which, due to the fault, might have a dangerous potential to ground.
The scope of this technical paper is providing the reader with the necessary information about the main normative aspects regarding protection against earth fault and indirect contact, clarifying the relevant problems and illustrating the solution proposed by ABB SACE
[ABB]Замыкания на землю, вызванные повреждением изоляции между токоведущим проводником и открытой проводящей частью, представляют определенную проблему при эксплуатации электроустановок, поскольку такие неисправности могут привести к выходу электрооборудования из строя и, кроме того, подвергают людей опасности поражения электрическим током. Это объясняется тем, что человек может прикоснуться к открытой проводящей части, которая в нормальных условиях не находится под напряжением, но из-за повреждения изоляции приобретает опасный потенциал относительно земли.
В рамках данного технического документа читателю будет предоставлена вся необходимая информация об основных нормативных аспектах, касающихся обеспечения защиты от замыкания на землю и защиты при косвенном прикосновении, при этом будут подробно рассмотрены существующие проблемы и описаны решения, предлагаемые ABB SACE.
[Перевод Интент]Тематики
- выключатель автоматический
- расцепитель, тепловое реле
- релейная защита
- электробезопасность
EN
- earth fault protection
- earth-fault protection
- ground-fault protection
- protection against earth fault
- protection against ground fault
- protection against ground-fault
DE
- Erdkurzschlussschutz, m
FR
Русско-немецкий словарь нормативно-технической терминологии > защита от замыкания на землю
15 кабельный трансформатор тока
кабельный трансформатор тока
-EN
cable type current transformer
a current transformer without primary conductor and primary insulation of its own, which can be mounted over an insulated cable
[IEV number 321-02-04]FR
transformateur de courant pour câble
transformateur de courant sans enroulement primaire et sans isolation propre qui peut être monté sur un câble isolé
[IEV number 321-02-04]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > кабельный трансформатор тока
См. также в других словарях:
conductor insulation — laido izoliacija statusas T sritis automatika atitikmenys: angl. conductor insulation vok. Leiterisolation, f; Leiterisolierung, f rus. изоляция проводника, f pranc. isolation de conducteur, f … Automatikos terminų žodynas
Insulation monitoring device — An insulation monitoring device monitors the ungrounded system between an active phase conductor and earth. It is intended to give an alert(light and sound) or disconect the power supply when the impedance between the two conductors drops below a … Wikipedia
insulation — 1. The act of insulating. 2. The nonconducting substance so used. 3. The state of being insulated. * * * in·su·la·tion .in(t) sə lā shən n 1) the action of separating a conductor from conducting bodies by means of nonconductors so as to prevent… … Medical dictionary
insulation — F/A/V material applied to a conductor that is used to isolate the flow of electric current between conductors and to provide protection to the conductor; also known as the dielectric … Audio and video glossary
insulation — Synonyms and related words: Jim Crow, aegis, alien, apartheid, buffer, bulwark, bumper, color bar, contraceptive, copyright, crash helmet, cushion, dashboard, division, dodger, ethnocentrism, exclusiveness, face mask, fender, finger guard, foot… … Moby Thesaurus
insulation — [1] Any material which does not conduct electricity. It is used to prevent the flow or leakage of an electrical conductor. [2] Any material which does not readily conduct heat. Used to keep heat or cold out of something. [3] The process of… … Dictionary of automotive terms
insulation, thermal — Material which is a poor conductor of heat; used to retard or slow down flow of heat through wall or partition … Dictionary of automotive terms
Electrical conductor — Overhead conductors carry electric power from generating stations to customers. In physics and electrical engineering, a conductor is a material which contains movable electric charges. In metallic conductors such as copper or aluminum, the… … Wikipedia
Building insulation — refers broadly to any object in a building used as insulation for any purpose. Whilst the majority of insulation in buildings is for thermal purposes, the term also applies to acoustic insulation, fire insulation, and impact insulation. Often an… … Wikipedia
thermal insulation — Material which is a poor conductor of heat; used to retard or slow down flow of heat through wall or partition … Dictionary of automotive terms
изоляция жилы — изоляция наложенная на токопроводящую жилу или экран по жиле [IEV number 461 02 02] EN conductor insulation insulation applied on a conductor or a conductor screen [IEV number 461 02 02] FR enveloppe isolante isolation appliquée sur une… … Справочник технического переводчика
Перевод: с русского на немецкий
с немецкого на русский- С немецкого на:
- Русский
- С русского на:
- Все языки
- Английский
- Немецкий
- Французский